Effective Date: November 8, 2026
Last Updated: November 8, 2026
VarioDeck is for informational and recreational use only. It is not a certified aviation instrument and must not be used as a primary flight or navigation instrument. Barometric readings drift with weather and pressure changes. Always use appropriate certified equipment and independent sources for safety-critical decisions.
Ground speed is not airspeed. GPS track is direction of movement, not necessarily where you are pointing. Never operate the app while driving or piloting. Cabin pressure changes can make altitude and climb/descent readings unrelated to your actual height.
Install VarioDeck on a compatible iPhone with iOS 17 or later, or Apple Watch with watchOS 10 or later.
Open the app. Sensor readings begin automatically; there is no Start button or account to create.
Allow Location While Using when asked, and any motion-related permission requested by the operating system. Enable Precise Location for better GPS results.
Go outdoors with a clear view of the sky and wait for readings to settle. Dashes mean a reading has not yet become available.
Open Settings using the gear on iPhone, or the Settings button on the Watch Trip page. Choose units and calibrate before relying on an estimate.
Absolute barometric altitude requires supported hardware, generally iPhone 12 or later or Apple Watch Series 6 or later. These hardware requirements are separate from the minimum operating-system versions. Relative barometric readings may work on other equipped devices. Without absolute altitude, Auto can use relative altitude with an available GPS baseline; without barometric readings, acceptable GPS elevation can provide a fallback. Check the displayed source rather than assuming a particular sensor is active.
The speed dial displays GPS-derived ground speed in mph, km/h or knots (kt). Its range automatically increases and decreases with current speed. The top values are 20, 40, 80, 160, 320 and 640, with a final 1,000-unit range. It steps up when speed exceeds about 95% of a range; 25 mph therefore uses the 0–40 mph range. The digital readout shows the measured speed, not the range maximum. Very small reported speeds below 0.3 m/s are shown as zero. Speed requires valid location readings.
A rotating compass card moves beneath a fixed marker and aircraft symbol. Read the heading at the top marker; the numeric readout includes a cardinal direction. Magnetic north is the default. Turn on Use true north in Settings to request true heading; magnetic heading is used if true heading is unavailable.
Where a valid compass heading is not available, the app can use GPS track while moving above approximately 1.5 m/s (3.4 mph). GPS track is not useful while stationary. Settings lists the heading source. A previously displayed heading can remain visible after the current source is lost, so check the source and do not assume that a visible number is fresh.
The cockpit-style analog altimeter includes a digital altitude window and feet/meters label. Use the digital window for an unambiguous number. Pressure is the sensor's ambient pressure, displayed in inHg or hPa; it is not automatically a sea-level weather report or the QNH you entered.
The altitude source appears above the iPhone panel, on the Watch Trip page and in Settings. Barometric uses supported absolute-altitude readings. Barometric (relative) uses a relative reading, with a GPS baseline when available. Until a baseline or manual calibration is set, relative altitude is not a reliable elevation above sea level. Barometric (QNH) derives altitude from measured pressure and your pressure setting. GPS means the app is using GPS altitude as a fallback. Demo data is simulated, not a measurement.
Zero is at 9 o'clock. Climbs move upward in green; descents move downward in orange. Feet mode labels the dial in hundreds of feet per minute (×100 FT/MIN); metric mode uses m/min directly. The numeric rate is smoothed over recent samples and can lag motion. Small numeric rates below 20 ft/min or 6 m/min are displayed as zero, even if the needle moves slightly.
In Settings > Vertical speed > Full scale, choose ±500, ±1,000, ±2,000 or ±6,000 ft/min, or ±150, ±300, ±600 or ±1,800 m/min. The needle stops at the selected scale's limit; the numeric rate can exceed it. Pressure changes can produce an apparent climb or descent even when you are not moving vertically.
Gain and loss add up upward and downward changes during the current app session. A roughly one-meter threshold reduces small noise contributions, but does not eliminate drift. High and low show the extremes of displayed altitude. Calibration changes can affect these extremes.
Use Reset on the main iPhone panel or Watch Trip page, or Reset gain and loss in Settings, to clear gain/loss and start high/low at the current altitude. For a fresh outing, calibrate first, then reset. Reset does not remove calibration or unit settings.
These statistics are held in memory, not saved as trip history. They may remain while the process stays alive, but are not restored after it ends. Updates pause in the background; this is not a continuous or background activity logger.
The Watch app uses the watch's own sensors and does not need the iPhone app running nearby. Each gauge scales to the available watch screen, reserving space for relevant readouts.
Swipe vertically or turn the Digital Crown to move through Vertical Speed → Altitude → Heading → Speed → Trip. On Trip, scroll to see gain/loss, high/low, Reset, Settings and the altitude source. The app stops sensor updates when it enters the background. It does not include a watch-face complication or extended background workout session. Phone and watch settings and totals are separate; no sync feature is implemented.
Open Settings > Altimeter. Allow readings to stabilize before changing calibration.
Choose Auto (barometer + GPS). Adjust Elevation in the currently selected feet or meters, then tap Set altimeter to this elevation. This stores a local offset so the current altitude matches your reference. Clear calibration removes that manual offset; it does not reset trip statistics.
In Auto mode, Use GPS elevation appears when an acceptable GPS elevation is available. Tap it to set the current altimeter to that value. It is a one-time calibration, not a promise of continuous GPS correction. GPS vertical accuracy is often poorer than horizontal accuracy.
Choose QNH setting and adjust the pressure stepper to a current local sea-level pressure setting, such as one from a nearby airport. The control displays your chosen pressure unit and supports 900–1,080 hPa (approximately 26.58–31.89 inHg). QNH mode uses the measured pressure; it requires barometric pressure readings. The Auto calibration offset is not applied in QNH mode. The app does not download weather or QNH: you obtain and enter the reference yourself.
Recheck calibration when weather changes or you travel to a different pressure region. Calibration cannot make this a certified instrument.
Altitude: feet or meters; also controls gain/loss and vertical-speed units.
Speed: mph, km/h or knots.
Pressure: inHg or hPa; also controls how the QNH stepper is displayed.
Full scale: VSI needle range, not a sensor accuracy setting.
Use true north: request true rather than magnetic compass heading where available.
Sources: inspect the current altitude and heading source.
Preferences are stored locally on each device. Changing units does not change the underlying measurements.
Use a current, trusted known elevation or QNH and recalibrate as conditions change.
Give GPS time to settle outdoors; buildings, trees and tunnels reduce reliability.
Keep the compass away from magnets, metal mounts and strong electrical interference.
Keep device sensor openings unobstructed. Wind, moisture and pressurized cabins can affect readings.
Expect lag from smoothing and measurement noise. Compare with independent references.
Active GPS and sensors use battery. The iPhone display stays awake while the app is active; lock the device or leave the app to stop active viewing. Sensor updates stop in the background, so missing intervals are not a complete trip record.
That is the current range, not a speed limit. The dial automatically expands as speed rises and contracts as it falls.
Barometric features may still work on supported hardware, but ground speed, GPS track and GPS calibration will be unavailable. Check permissions in device Settings if GPS readings are missing.
Weather changes pressure; sensors also have noise. Recalibrate against a known reference. Gain/loss can accumulate drift despite its noise threshold.
No. There is no map, saved route, trip archive, export, account or cloud sync. Live readings and session statistics are not persistently saved. Only preferences and calibration settings are retained.
The app makes no network requests of its own, and the Watch app runs independently. Device location services and reception still affect available readings. No live weather is fetched.
Simulator builds automatically use demo data. A real compatible device is required to evaluate actual barometric pressure and altitude.
No. VarioDeck is for informational and recreational use only. It is not a certified aviation instrument and must not be used as a primary flight or navigation instrument. Barometric readings drift with weather and pressure changes. Always use appropriate certified equipment and independent sources for safety-critical decisions.
For help, email jasonburt@tyloal.com. Include your device model, operating-system version, the gauge/source involved and what you expected. Do not send sensitive location information.
Developer: Tyloal (Jason Burt)
Email: jasonburt@tyloal.com
Website: www.tyloal.com
Privacy Policy · Terms of Service